国产大学生粉嫩无套流白浆-91久久精品一区二区-日韩久久免费精品视频-少妇性l交大片欧洲热妇乱xxx

濟南方圓硬度計 0531-83157169
您的當前位置: 主頁 >> 行業新聞

沖擊試驗機八大經常出現的故障

行業新聞

瀏覽:81次 2020/05/27

八大沖擊試驗機...

八種主要的沖擊試驗機經常出現...

作為控制產品質量的必要設備,在使用過程中如何進行故障排除,請確保機器正常運行...

通訊...

撥盤指針的靈敏度很差,并且在撥動指針后會中途停止...

這種現象的發生...

1.在機架上滑動...

這時,您需要將其移除并清洗,然后添加...

2...

3.機架桿和...

4。...

5.測力活塞上的皮帶脫落或掉落。...

6.力測量活塞在油缸中的摩擦力增大或變?yōu)閟tu...

7.擺錘上升過程中有障礙物,或者擺錘軸太臟或...

經常...

進行拉伸測試時,樣品...

這種現象的原因...

主體安裝是否垂直,如果...

1. When the jaws are not clamped properly, the specimen should be clamped symmetrically as required....

2.顎......

At this time, the jaws should be replaced....

3. The lifting guide wheel is not adjusted correctly, so that the upper and lower jaws are not concentric....

An inspection should be processed...

Common fault three:...

The position of the pendulum is abnormal, and the pendulum is not aligned vertically....

The main reason is that the viscosity of the oil is too large or the oil is too dirty....

2.…………。...

測力活塞隨...

elimination method...

There is unstable friction....

排除方法:清洗回轉軸軸承,齒輪桿,...

排除方法:清洗擺...

排除方法:清洗擺動軸軸承,變...

排除...

但是,如果緩沖器的油孔被堵塞,或...

解決的辦法是...

放置油針旋鈕,使油針之間的間隙...

放置油針旋鈕,使油針與閥...

放置油針旋...

p...

消除方法是取下表盤玻璃并調節...

消...

消除方...

First, check whether the joint of the oil circuit system is tightened. If you need to replace the gasket, replace it in time....

如果管道損壞,則需要更換...

如果管...

Sample break...

除根據修道院的規定外,主要是緩沖區的故障...

始終注意使用測試儀時發現的問題,并安排...

對吧...

就...

Shock...

影響力的價值...

如果指示值太,則可以將調零螺絲向上調至最大...

如果the...

另外,如果樣品在沖擊試驗機上的壓縮力太大,則指示值會更; 否則,指示...

友情鏈接 / links